Pnömatik vakum besleyici arızalandığında ne yapmalıyız??

The pnömatik vakumlu konveyör uses compressed air to generate high vacuum through a vacuum generator to realize the conveying of materials, Pnömatik vakum besleyici arızalandığında ne yapmalıyız?. Gereksinimler, vesaire. The high vacuum generated by the vacuum generator eliminates the layering phenomenon of the conveyed materials and ensures the uniformity of the composition of the mixture. And other mechanical automatic feeding equipment.

When the compressed air is supplied to the vacuum generator, the vacuum generator will generate negative pressure to form a vacuum airflow, and the material will be sucked into the suction nozzle to form a material airflow, which will reach the silo of the feeder through the suction pipe. The filter completely separates the material from the air. Malzeme siloyu doldurduğunda, kontrolör hava kaynağını otomatik olarak keser, the vacuum generator will stop working, and the silo door will automatically open, ve malzeme ekipmanın haznesine düşecektir. Aynı zamanda, Basınçlı hava, darbe geri yıkama valfi aracılığıyla filtreyi otomatik olarak temizler. When the time is over or the material level sensor sends out the feeding signal, besleme makinesi otomatik olarak başlatılacaktır. The machine uses high-pressure air to blow back, which can instantly shake off the powder, so that it maintains a good effect.

Ne zaman pnömatik vakumlu konveyör fails, the treatment methods are as follows:

If the feeding machine fails to feed or the feeding capacity is low, please check according to the following procedures.

1. Whether the air supply pressure of the system reaches 0.5-0.6Mpa. Air supply pressure refers to the air pressure in the system when the vacuum generator is working.
2. Whether the discharge door is tight.
3. After a long time of use, a certain thickness of powder accumulates on the discharge door, which causes the door to not close tightly and leaks vacuum. The discharge door should be cleaned. The sealing rubber ring of the discharge door is worn, causing the door to close loosely and leaking vacuum. The sealing ring should be replaced. If the output and stroke of the cylinder are faulty, the cylinder should be replaced.
4. Filter is clogged. After blowing the filter clean with compressed air, blow back the filter with your mouth. If it is smooth, the filter is not blocked; if you feel suffocated, the filter has been blocked. Put it in an ultrasonic cleaner for more than 30 dakika.
5. The suction tube is blocked by a large piece of material. It often occurs at the entrance of the stainless steel suction nozzle and the entrance of the vacuum hopper.
6. The clamps between the pump head and the hopper and between the sections of the hopper are not tightened, causing the system to leak air, unable to feed materials or reducing the feeding capacity.
7. The backflush system has failed. The compressed air pulses stored in the air bag back-blow the filter each time the vakum taşıyıcı discharges to ensure that there is only a thin layer of powder on the surface of the filter. If the backflushing system fails, thick powder will accumulate on the surface of the filter, increasing the resistance and causing the vacuum feeder to fail to feed. Şu anda, the backflushing valve should be replaced.

Eversun makineleri (Henan)eş,.Ltd kuruldu 2003, Eversun Makine eleme ve ekipmanı taşıma profesyonel bir üreticisidir, ürün kalite sistemi kesinlikle ISO9001 tarafından onaylanmıştır:2005 ve CE ulusal standartlar.

Ana ürünümüz eleme makinesidir., Vibro filtresi, Ultrasonik titreşimli elek, Vakum konveyör, Dumpting station etc

Herhangi bir desteğe ihtiyacınız olursa lütfen bizimle iletişime geçmekten çekinmeyin.

Satış Departmanı: Sales@vibrosievingmachine.com, Cell/WhatsApp:+86 13162301696